Mensagens Storage

Algumas mensagens de Storage


IGW038A Possible PDSE Problem(s)
IGW038A Recommend issuing V SMS,PDSE,ANALYSIS

Quando esta mensagem aparecer, o comando da mensagem deve ser aplicado.

Esta é a resposta do comando que deve ser verificada:

IEE712I VARY SMS PROCESSING COMPLETE
IGW031I PDSE ANALYSIS Start of Report
+no exceptional data set conditions detected
PDSE ANALYSIS End of Report


IEC604I VTOC CONVERT ROUTINE ENTERED ON

Esta mensagem indica que o tipo de leitura de Datasets VTOC pode estar com problemas. O suporte técnico de Storage deve ser contactado.


ARC0560E MIGRATION LIMITED: NO MIGRATION LEVEL 1 SPACE
Contact DASD ASAP - ARC0560E MIGRATION LIMITED: NO MIGRATION LEVEL 1 SPACE

Esta mensagem pode ser verificada usando alguns comandos de HSM que estão nó tópico, caso necessário, contactar o suporte técnico. O parametro a ser checado é o MIGRATION.


ARC0050ADFHSM IS NOT ACTIVE - START DFHSM; call Storage Administration

Esta mensagem indica que o HSM ou DFHSM deve ser verificado e se necessário, contactar o suporte técnico.


OCDS CONTROL DATA SET IS ABOUT 081%

Esta mensagem indica que o OCDS está com Log de 81%. Este parametro é configurado para alertar por volta de 80%, mas normalmente é crítico aos 90%. O parametro a ser configurado para alarmar é o Threshold.


ARC0911E OCDS INDEX DATA SET IS ABOUT 091% FULL

Mensagem que indica que o Data Set index do OCDS esta enchendo, se nao consguir resolver por comando, contactar Storage.


ARC0909E BCDS CONTROL DATA SET IS ABOUT 081% FULL
TOA1087A BCDS CONTROL Data Set has exceeded the threshold.

Esta mensagem indica que o Threshould do BCDS que é um Dataset de controle do HSM, foi excedido. O Operador normalmetne chama o suporte técnico após os 90%. Mas pode depender de cada sistema.


ARC0717I AUTOMATIC BACKUP TERMINATED PRIOR TO 753 COMPLETION, QUIESCE TIME REACHED
ARC0699I AUTOMATIC BACKUP ENDING EXCEPT FOR POSSIBLE 754 RETRIES OF IN USE DATA SETS
ARC0721I AUTOMATIC BACKUP ENDING

Esta mensagem se investigada na Log do sistema, indica um Job que geralmente pertence ao time de Storage, e este Job que provavelmnte faz algum Backup, pode ter tido problema. Portanto, o time de Storage deve ser chamado.


#IEC210I 214-10,IFG0200Y,XXXXXXXX,STEP010R,SYSUT2,011A, H99999, XXXXX.YYYYY.WWWWWWWW.ZZZZZZZZ.KKKKKKK

Explicacao do suporte de Storage sobre a mensagem:

The error occurred during processing of a CLOSE macro instruction for a data set on magnetic tape. The number of blocks processed, which is determined by the position of the tape, does not match the number of blocks specified in the DCB. This error can occur if a cancel command is issued during the time a QSAM tape output job using more than one output buffer is executing. Canceling the job might cause an abend 210 with return code 10.

Explicacao do Programados de Aplicacoes:

If an I/O error has occurred, a defective volume or device might be the cause. Save the output from the failing job to aid in the analysis of the problem.
Rerun the job specifying a different volume or device. If a scratch volume was being used when the I/O error occurred, request a different volume. If that does not solve the problem, request a different device in the UNIT parameter of the DD statement. If a specific volume is needed, try requesting a different device in the UNIT parameter of the DD statement. Rerun the job.


IEC604I VTOC CONVERT ROUTINE ENTERED ON D084,T1CRX2, DOS

Chamar o suporte de Storage.


AUTOMIGRATION NOT RELEASED - PREVIOUS HOLD (CONT.) COMMAND STILL IN PROGRESS

Mensagem que indica que algo possa estar parado no HSM. Usar o comando Q ACT e chacar o parametro. Se tiver algum prmelam mesmo, chame o time de Storage.


Unless otherwise stated, the content of this page is licensed under Creative Commons Attribution-ShareAlike 3.0 License